Faux Brick or Stone Headboard Wall: Panel Counts by Bed Size

Plan a headboard accent wall in whole panels and the count is simple: three panels across and three rows high is 9 panels, exactly one Pack of 9, covering about 118″ × 59″ (300 × 150 cm). That band is wider than any standard mattress, king included. A twin, full or queen can also take a two-panel-wide band of 6 or 8 panels, and a full bedroom wall is counted by area instead. Every number below comes from one fact on our faux brick panel pages: each panel is 39.4″ × 19.7″ (100 × 50 cm) and covers about 5.38 sq ft.

Choose a headboard band or the whole wall first

There are two ways to put brick or stone behind a bed, and they are counted differently.

• A headboard band is a rectangle of panels centered behind the bed, usually three or four rows high. It uses fewer panels and can be sized in whole panels, so there are no horizontal cuts. Its sides and top leave the panel edge exposed, so decide how you will finish them before you start.
• The whole wall runs corner to corner and floor to ceiling. The room's corners and ceiling line hide the panel edges, but the top row and the last column usually need trimming, so you order a margin for cuts.

If the bed wall has a window, outlets at both ends and a corner you would rather not wrap, the band is usually the calmer project. If the wall is narrow and has nothing to cut around, the full wall adds only a few panels and hides every edge.

Size the band in whole panels, starting from the mattress

Laid with the texture running horizontally, as in our product photos, one panel spans 39.4″ across and 19.7″ up. Rows stack in steps of 19.7″: three rows reach 59.1″ (150 cm), four rows reach 78.8″ (200 cm). A fifth row would reach 98.5″, taller than an 8 ft ceiling, which is why floor-to-ceiling walls always end with a trimmed top row.

Width works the same way: two panels make a 78.8″ (200 cm) band, three make 118.2″ (300 cm). The table compares those widths with standard US mattress widths. A bed frame or headboard can be wider than the mattress, so measure your own bed before you choose.

Turning panel counts into packs:

• 6 panels (about 32.3 sq ft): three Packs of 2.
• 8 panels (about 43 sq ft): four Packs of 2, or one Pack of 9 with a spare.
• 9 panels (about 48.4 sq ft): one Pack of 9.
• 12 panels (about 64.6 sq ft): one Pack of 9 plus two Packs of 2, which leaves a spare, or six Packs of 2.

If you offset alternate rows by half a panel, the two half panels at the ends of the offset row come from a single panel, so the count stays the same. A spare panel is still worth having if an outlet or switch falls inside the band, in case a cut-out goes wrong.

Count a full bedroom wall by area, then add 10 percent

For a wall-to-wall finish, multiply the wall's width by its height in feet, divide by 5.38, round up, then add about 10% for offcuts at the edges and around outlets and switches. That is the same method our step-by-step installation guide uses.

Buyers lean toward the larger pack. In the twelve months to October 2026, the Pack of 9 outsold the Pack of 2 on each of our four best-selling designs, 154 packs to 61 in total. Most of our product pages pitch the Pack of 2 for small accents or for sampling a texture before a larger order.

Match the texture to the bedroom you already have

A headboard wall sits behind the bedding and the nightstands, so pick it against what stays in the room. All of the designs below name bedrooms on their product pages.

• Warm, lived-in brick. Earthcore mixes distressed greys, warm browns and faded reds, and it was our best-selling design over the same twelve months. Babylon is classic red-brown brick, and its product page lists a bedroom headboard backdrop among its uses. Both sit well with oak or walnut furniture and plain bedding.
• Quiet stacked stone. Gemstone layers earthy greys, taupes and muted charcoal in horizontal lines; it was our best-selling stone design. Slate blends earthy greys with warm beiges and brown undertones. Both suit grey or white linens.
• Light and soft. Limestone combines light greys and soft whites with warm beige undertones, for a bedroom where a dark wall would feel heavy.

Plan the bed, lamps and outlets before the panels go up

The panel face sits in front of the old wall surface. On the Earthcore and Gemstone panels, our product photos show a thickness of 0.8″ (2 cm), and that edge is what shows along the sides and top of a band.

• Mark the band on the wall with the bed pushed back in place, then pull the bed out to work. Center the band on the bed, not on the wall.
• Leave the bed a little off the wall once the panels are up, so a headboard does not rub the raised texture every night.
• Keep lamps on the nightstands. Plug-in bedside lamps avoid fixing anything through the panels (see the first question below).
• Find the outlets and switches that fall inside the band and plan the cut-outs. Our guide to cutting panels around outlets and corners covers measuring and cutting them.
• Check the wall surface. The product pages call for a smooth, flat wall.

For fixing, the product page of our high-tack montage adhesive says to "Apply 15 small adhesive points (dabs) evenly across the back of the panel" and then "Lightly press the panel onto the wall for a secure fit", using a heavy-duty professional caulking gun rather than a lightweight plastic one. The adhesive is sold separately from the panels.

Give the order a buffer before holiday guests arrive

If the wall needs to be finished before Thanksgiving on November 26, work back from the delivery, not the order date. Under our shipping policy, stock items ship within 3–5 business days with FedEx or UPS, tracking is emailed when the order ships, and shipping is free within the contiguous United States. Transit time comes on top of that, so order with room to spare and keep a weekend free for the wall itself.

When the boxes arrive, lay the panels out on the floor in the band's shape before any glue goes on. It is the easiest way to check the count, see how the tones sit next to each other, and catch an outlet you missed.

Questions about faux brick and stone headboard walls

Can I hang a headboard, shelf or reading light on the panels?

We don't recommend it. Our product pages describe the panels as a glue-on wallcovering and give no load rating, so nothing should hang from the foam itself. A bed frame with its own headboard and lamps standing on the nightstands keep the panel wall free of fixings.

Can I take the panels down when I move out?

Treat the wall as permanent. The adhesive is sold for "a secure, lasting hold", and our product pages do not describe a removal method. If you rent, ask your landlord before you start.

Will a panel wall make the bedroom quieter?

Our product pages say the dense foam "softens ambient noise", but they give no sound rating, so don't count on it to block noise from a neighbor or the next room.

Can I see the texture before I buy a whole wall?

Yes. Every design is sold in a Pack of 2, and most of our product pages suggest that size for sampling the texture before a larger order. Two panels side by side are 78.8″ wide, enough to hold up behind the bed and judge the color against your bedding.

Compare all the textures side by side in our faux brick wall panels and faux stone wall panels collections. Every design comes in a Pack of 2 or a Pack of 9, with the same 39.4″ × 19.7″ panel size.

---

Panel sizes and coverage are taken from our product pages; mattress widths are standard US sizes. Sales figures cover orders from October 2025 to October 2026. Photographs are of our own panels. Illustrative images marked as such were generated with AI; product photographs are of our own products. This article was prepared with AI assistance and reviewed by the SnapMasons team before publication.